RORO Cargo Ships And Vehicle Carriers That Were Converted Into ROPAXes In The Philippines

RORO (Roll-on, Roll-off) Cargo Ships differ from ROPAXes (RORO-Passenger Ships) in that the former are mainly for carrying rolling cargo (vehicles mainly but could also be heavy equipment) with their drivers and crew and as such their passenger capacity and amenities like a restaurant or cafeteria are small. They are mainly designed to ferry vehicles across the sea with the least loading and unloading time. Their sizes vary depending on the distance and the traffic volume. Generally, they have higher sides.

In the Philippines, they are represented currently by the Super Shuttle RORO 7, Super Shuttle RORO 8, Super Shuttle RORO 9, Super Shuttle RORO 10, Super Shuttle RORO 11 and the Super Shuttle RORO 12 of the Asian Marine Transport Corporation (AMTC). They are also represented by the Dapitan Bay 1, Panglao Bay 1 and Batangas Bay 1 of Carlos A. Gothong Lines Inc. (CAGLI). But this selection is the relatively large ones by RORO Cargo Ship standard. There were smaller versions of it in the past.

Vehicle Carriers are similar to RORO Cargo Ships but instead of acting like commuters they deliver vehicles from the factories to a destination and so they will come back without load unlike the RORO Cargo Ships.  Vehicle Carriers could be smaller or bigger than RORO Cargo Ships but lately they began growing bigger to be more efficient in bringing new cars from the likes of Japan to the United States. Those delivering cars within Japan only were considerably smaller.

In the Philippines, there were several RORO Cargo Ships and Vehicle Carriers that were converted into ROPAXes or what is commonly called as ROROs here and most became RORO Liners of the major liner companies. Per ton, a RORO Cargo Ship or a Vehicle Carrier is cheaper than a ROPAX as it doesn’t have that much equipment and amenities for passengers. Besides, for the same size, they could have smaller engine/engines and so the speed is a bit less.

In refitting, it is possible that in a RORO Cargo Ship or a Vehicle Carrier that metal has to chopped off. Meanwhile, locally, it is normal to add metal to a ROPAX from Japan to add decks for more passenger accommodation. Viewing areas were not considered in the building of RORO Cargo Ships and Vehicle Carriers and that could be one reason for chopping off metal.

I noticed that RORO Cargo or Vehicle Carrier conversion here goes by streaks by shipping lines that has a liking for them for the benefits they offer like a smaller capital cost for the same capacity and I agree with them it is a route worth taking. Maybe the first who took this route was the K&T Shipping Lines which was later known as the Maypalad Shipping Lines after their ferry Kalibo Star sank in Samar Sea in the late 1990s.

Samar Star

Many do not know that K&T Shipping was among the first in the acquisition of ROROs and maybe one reason for that is their ROROs do not look like the traditional ROROs of the other shipping lines. Their first RORO was the Samar Queen that was later renamed into Samar Star which actually became their last ship existing but not sailing. This ship was classified as a Ferry-RORO in Japan but she has the looks a cargo ship like a trio of sister ships K&T Shipping later acquired – the Leyte Star (a.k.a. Leyte Queen), the Cebu Star (a.k.a. Cebu Queen) and the Kalibo Star (a.k.a. Ocean Star). The difference is these four ships have rear-quarter ramps and a car deck and in order for them to carry passengers, K&T Shipping built a passenger deck atop the car deck. In Japan, the trio was classified as Vehicle Carriers.

Leyte Star

The Leyte Star by Edison Sy of PSSS.

The Samar Queen was smaller than the three sister ships at 56.6m x 9.0m x 5.6m and she arrived in 1980 which was just the dawn of RORO (more exactly ROPAX) shipping in the Philippines. Meanwhile, the Leyte Queen arrived in 1984 and the Cebu Queen arrived in 1986. Then the ill-fated Kalibo Star arrived in 1992. All of the three were former Toyo Maru ships in Japan but they have different owners. The external measurement of the Kalibo Star was 72.0m x 10.4m x 4.5m and the measurements of the other two sister ships hew closely to this.

The trio of sister ships were powered by a single 1,250-horsepower Hanshin engine which gave a design speed of 12.5 knots. The Samar Star has a single 1,300 Nippatsu-Fuji engine giving a speed of 13 knots. And this brings up one characteristic of small RORO Cargo ships and Vehicle Carriers. They are generally powered by a single engine only whereas ROPAXes of their size almost invariably have two engines and are faster.

Cebu Star

Cebu Star by Rex Nerves of PSSS.

These four K&T ships have one of the minimum conversions in this type of ships. At the start, the passengers just have to unroll cots and look for a place that they prefer.  Their main cargo here was not rolling cargo either. Nothing unusual in that as most Cebu overnight ferries carry loose and palletized cargo in the main. In loading and unloading, forklifts are used just like in the other Cebu overnight ferries.

Before I digress further, the first of this type of ships converted into ROPAX might be the Don Carlos of Sulpicio Lines Inc. which arrived in 1977 and was classified as a Vehicle Carrier in Japan. Actually, the Don Carlos could very well be our very first ROPAX that is not an LCT. This ship was formerly the Daiten Maru of the Masumoto Kisen KK in Japan. She also not carried rolling cargo except for some trucks and heavy equipment destined for the South (her route is to General Santos City) and on the return trip livestock was loaded. She suffered a piracy attack in 1978 and later she was just used as a cargo ship.

1978 0508 Hijacked Ship

Research by Gorio Belen in the National Library.

The Don Carlos measured 71.6m x 10.9m x 4.9m which is almost the same of the measurements of the K&T Shipping sistership trio. However, this Sulpicio ferry looks like a regular ROPAX after refitting. She was equipped with a single Hanshin engine of 1,300 horsepower and her design speed was 12.5 knots and that speed was her one weakness as she was sailing a long route.

The second shipping company that had a liking for this type of ship to be converted as ROPAXes was the Carlos A. Gothong Lines, Inc. (CAGLI). This happened when they were building up their fleet so that they can return to their Manila route after her break-up with Lorenzo Shipping Corporation. After the break-up Gothong Lines concentrated on the Visayas-Mindanao routes but they relied on small ROPAXes. For the Manila route, they needed bigger ships and acquiring this type I am discussing was their route.

Their first of this type converted to ROPAX might have been the Our Lady of Guadalupe which was Asaka Maru No.8 in Japan and was classified as a Ferry-RORO. But to me she has the built of a Vehicle Carrier which meant metal has to be taken off rather than added like what happens in the former ROPAXes of Japan brought here. One thing notable in the Our Lady of Guadalupe is the high sides with few viewing areas for passengers. The two traits are traits of Vehicle Carriers.

Our Lady of Guadalupe (2)

Our Lady of Guadalupe by Toshihiko Mikami of PSSS.

The Our Lady of Guadalupe measured 89.7m x 14.4m x 4.8m with a passenger capacity of 674 persons. She was powered by two Niigata engines with a total of 5,400 horsepower and her top sustained speed when new was 16 knots. She was fielded in the Manila route in 1986 before being downgraded by Gothong Lines to the Cebu-Surigao route in the early 1990s and she had the reputation of being unreliable and that helped the new Cokaliong Shipping Lines Inc. to survive in the route. Her unreliability was never resolved even when she was passed on to the Cebu Ferries Company after the “Great Merger” of 1996.

In 1990, Gothong Lines acquired a pair of sister ships classified as RORO Cargo ships in Japan. The two are the Shinsei Maru which became the Our Lady of Sacred Heart and the Shinka Maru which became first as the Sto. Nino de Cebu. The latter suffered a fire early on after fielding (how can a ship with such a magical name catch fire?) but she was repaired and she was renamed into the Our Lady of Medjugorje. The two are among the better conversions that I have seen and in the latter I love her verandas and she was among my favorite ships.

OUR LADY of SACRED HEART

Our Lady of Sacred Heart by Chief Ray Smith of PSSS.

The sister ships have already been lengthened in Japan and they measured an identical 123.0m x 18.0m x 12.3 meters and that size was average for many of the liners that came in 1990-92 although their passenger capacity did not reach 2,000 persons. The two were not built in the same shipyard. The Our Lady of Sacred Heart was built by Tsuneishi Shipbuilding in 1978 and the Our Lady of Medjugorje was built by the Mitsui Engineering & Shipbuilding in 1979. The first had a single 9,000 horsepower Mitsui engine while the latter had a single 8,000 horspower engine but both had a design speed of 17 knots which became 16.5 knots in the country. In the “Great Merger” they were transferred to WG&A and they continued to ply a route from Manila and sometimes pairing with each other as they have the same speed (sometimes with SuperFerry 3 too that also has the same speed with them).

Our Lady of Medjugorje (Aboitiz)

Our Lady of Medjugorje by Albritz Salih of PSSS.

A related company, the Cebu Ferries Corporation (CFC) acquired in 2009 and 2010 two ships, the Asakaze and Esan which became the Cebu Ferry 2 and Cebu Ferry 3. In Japan they were classified as Ferry-ROROs but they do not look like the type. They might have a small passenger capacity but both featured open car decks and so plenty of metal has to be added in them to become ROPAXes. I do not consider the two part of the type I am discussing.

When Carlos A. Gothong Lines Inc. divested from WG&A, their first acquisition in 2001 when the divestment was not yet complete was actually a RORO Cargo ship, the Koyo Maru of Keiyo Kisen which became the Butuan Bay 1 in their fleet. At 114.8m x 19.0m x 9.6m, she was not a small ship. What are striking about her was her height and the length of her ramp. The ship was built by Iwagi Zosen in 1989 and she is powered by a single Mitsubishi-MAN engine with 9,600 horsepower that gave her a speed of 17.5 knots.

Butuan Bay 1 in Iligan City

Butuan Bay 1 by Josel Nino Bado of PSSS.

However, her refitting was not first-class (two passenger decks were just added atop her decks) and so when she was sold to Trans-Asia Shipping Lines Inc. (TASLI) in 2010 after an engine room explosion, TASLI remodeled the ship comprehensibly and she became a looker as the Trans-Asia 5. However, when MARINA took exception to her conking out and wallowing in water (the disadvantage of a single-engine design), she was reverted into a cargo ship and parts of her superstructure were removed. Still, she is a good-looking ship.

Trans Asia 5

The old Trans-Asia 5 by Michael Roger Denne of  PSSS.

Trans-Asia 5

The new Trans-Asia 5 by Mike Baylon of PSSS.

Recently, another shipping company took as liking for this type to be converted into ROPAXes. This is the Asian Marine Transport Corporation (AMTC) which also operates many RORO Cargo ships for their cargo liner operations. Their conversions started their Super Shuttle RORO series but it stopped at three as it seems they found out they were not really good in passenger liner operations.

Their first ship converted was the small RORO Cargo ship Cebu Trader which became the Super Shuttle RORO 1. This ship was built in 1978 by Trosvik Verskted in Norway and has passed into many hands already which is normal in Europe especially for this type. She measured 97.2m x 16.6m x 6.4m and she was powered by two Hedemora engines with a low total of 2,600 horsepower but still her design speed was 14.5 knots (which is a little doubtful).

Super Shuttle Roro 1

Super Shuttle RORO 1 by Fr. Bar Fabella, SVD of PSSS.

AMTC acquired this ship in 2011 and she was tastefully and even moderniscally refitted in Ouano port for ASR in Mandaue, Cebu which showed none of her age. However, she did not serve long as in 2012 she caught fire in heavy downpour while taking shelter from a tropical storm in Looc Bay in Tablas Island, Romblon on a route from Batangas to Dumaguit via Odiongan. She was never repaired.

The next in the series actually came in 2010 and was a small Vehicle Carrier. This was the former Koyo Maru No. 23 in Japan which became the Super Shuttle RORO 2 for AMTC after conversion. The ship measures 90.0m x 14.2m x 11.6m and she is powered by a single Hanshin engine of 3,200 horsepower which gave her a top speed of 14.5 knots when was still new.

Super Shuttle Roro 2

Super Shuttle RORO 2 by Raymond Lapus of PSSS.

However, even with an equal design speed it was said she was faster than the Super Shuttle RORO 1 in the same route to Dumaguit port in Aklan. Well, this ship was built later in 1987 by Imamura Shipbuilding in Japan and that could be a difference. Super Shuttle RORO 2 still sails in the same route but sometimes she takes long breaks.

The last ship in the series is the biggest of the three at 128.8m x 19.9m x 6.6m which is already not small for a liner but she was not developed well and her Tourist section was not even finished. This ship was the Vehicle Carrier Atsuta Maru in Japan that was built by Kanda Shipbuilding and she was named as the Super Shuttle RORO 3 in AMTC. Her route is Batangas-Masbate-Mandaue-Cagayan de Oro and with unfavorable arrivals and departures she never became popular with the passengers especially when her departure times became hard to divine as the company gave priority to cargo. However, her cargo load is always good.

Super Shuttle Roro 3

Super Shuttle RORO 3 by Aris Refugio of PSSS.

Recently, she no longer takes in passengers. Before she was a cheap, direct ride to Batangas but the passengers have to bear hardships. I was lucky I was able to ride her when she was still taking passengers. There were times too when she became unreliable and can’t sail for extended periods of time. She has a single 8,000 horsepower Hitachi engine which powers her to 18 knots when still new. Her unreliability seems to stem from maintenance problems.

Roble Shipping Inc. also tried this type of conversion when they acquired the Vehicle Carrier Taelim Iris from South Korea in 2015. They did not immediately do work on the ship and when work commenced it was just done in their wharf in Pier 7 in Mandaue, Cebu. A lot of metal was added but after the work was finished a beautiful Oroquieta Stars emerged which became their pride. Originally meant for Misamis Occidental, she became a regular to Baybay, Leyte where she is a favorite.

Oroquieta Stars

Oroquieta Stars by James Gabriel Verallo of PSSS.

The Oroquieta Stars measures 77.4m x 12.0m x 8.1m and she is equipped with two Akasaka engines with a total of 4,900 horsepower. Her design speed is 16 knots and that is more than enough for a Leyte overnight ship. She was built by Sanyo Shipbuilding in Japan in 1994.

Another company which tried this conversion route was the Aleson Shipping Lines of Zamboanga. They acquired the Ariake Maru No.18 in 2016, a Vehicle Carrier in Japan built by Honda Shipbuilding. This ship has high sides and to have passenger viewing areas and access, metal has to sloughed off. In the Aleson fleet, this ship became known as the Antonia 1 and named after the matriarch of the company.

52315746_2330050103986854_4842633140147060736_n

Antonia 1 by Albritz Salih of PSSS.

The Antonia 1 measures 103.6m x 15.5m x 11.5m and she is powered a single Akasaka-Mitsubishi engine of 4,000 horsepower. Her design speed is 15 knots. Presently, the ship’s route is Zamboanga-Sandakan, our only international passenger ship route.

The last company which tried this route of conversion is the Trans-Asia Shipping Lines Inc. (TASLI). They acquired the Warrior Spirit in 2016 and even earlier than the Antonia 1. While the Antonia 1 sailed in 2017, the Warrior Spirit which was renamed into the third Trans-Asia still can’t sail as a host of ailments that defied easy solutions bugged her especially in the engine department.

39441733_1940977989258472_3367702600030879744_n

Trans-Asia by C/E John Nino Malinao Borgonia of PSSS

The ship was built by Nouvelle Havre in France in 1980. Trans-Asia, the third, measures 126.2m x 21.0m and her design speed is 19 knots. With high sides and being tall, this ship is the biggest-ever of Trans-Asia Shipping Lines. And I hope that finally they will be able to solve her problems.

I am not too sure if my list is complete. But I would want to see in the future what other ships of this type will be converted into ROPAX in our country again.

 

 

 

Advertisements

Philippine Ferries That Are Celebrating Their Golden Anniversaries In 2017

There are a few ferries in the Philippines which will be having their golden anniversaries this year because they have already reached 50 years of existence and sailing. That means these were built exactly in the year 1967 and all of these ferries are testaments to their design and engineering. It is also a testament to the Philippine side from the owners to the engineers for their loyalty and belief in their ships.

Not all of these ships are in the pink of health now, of course. In humans they might be the equivalent of our centenarians. But unlike our centenarians these are not exactly laid-up vessels and if not sailing they are being held in reserve. Some of these have hiccups at times but those episodes are not something that cannot be repaired. And unlike planes where there is always an emergency when an engine conks out, in ships even though it loses main engine power they simply become the equivalent of unpowered barges and barges sail day in and day out in all waters of the world.

Here then are our “golden” ferries this year:

Maybe we should start with the Maria Gloria of Montenegro Shipping Lines Inc. (MSLI). This is a notable ship because she was the first steel-hulled ferry of Montenegro Lines. She came to our country in 1994 when she was already 27 years old and she has been a good ship from the time she arrived and is still a very reliable ship until now. It looks like Montenegro Lines is taking care of her very well.

MV Maria Gloria (Ang barko na paborito ko!)

Maria Gloria by Raymond Lapus

The Maria Gloria is a short-distance ferry-RORO and for a long time served the Mindoro routes although at times she can also be found in the route to Siquijor. She was built as the Tenyo Maru for the Shimabara Tetsudo by Kanda Shipbuilding in Kure, Japan. She measures 42.9 meters by 11.0 meters and she has a passenger capacity of 413 persons. She is powered by twin Daihatsu engines with a total of 1,400 horsepower which is still good enough for some 10 knots today.

Another 50-year old ship in the fleet of Montenegro Lines is the ferry Maria Isabel which holds for the company their Iloilo-Cuyo-Puerto Princesa route across the wide Sulu Sea. Now if she is not a reliable ship Montenegro Lines won’t assign her to that route especially since swells can be powerful in her route when the monsoons are acting up.

8518402772_f87ba471e0_z

Maria Isabel by Carl Jakosalem

The Maria Isabel was originally the Shirakawa Maru in Japan and she was built by Taguma Zosen in Innoshima, Japan. Her external dimensions are 49.0 meters by 13.2 meters and she has a passenger capacity of 427 persons. A two-deck overnight ferry, her Gross Tonnage is rather high for her Length at 836 (this figure has no unit). She is powered by twin Hanshin engines of 1,700 horsepower and her design speed is high at 14.5 knots and maybe this was the reason she was assigned the long Sulu Sea route.

The Maria Isabel arrived in the country in 1997 when she was already 30 years old. Now who said imported surplus ferries should be no more than 20 years old? I say it depends on the condition of the ship. Maria Isabel has two sister ships in the Philippines and both are in the fleet also of Montenegro Lines. These are the Maria Erlinda and Maria Rebecca.

Another “golden” ship in the Philippines is one that has a complicated history and is a survivor. She first arrived in the country in 1982 as the first RORO ferry of Viva Shipping Lines which were formerly operators of motor boats like Montenegro Lines. The ship was 15 years old then, a relatively young age and she was named as the Viva Santo Nino.

The Viva Santo Nino was formerly the Bisan Maru of Sanyo Kisen of Japan. She was built by Kanda Shipbuilding in Kure, Japan and she measures 50.0 meters by 11.8 meters. Originally 665 GRT in Japan but here her GT was deflated. I am not sure of her original engines but later it were two Yanmar engines totaling 1,800 horsepower which was good for 13 knots.

The Viva Santo Nino sailed well for Viva Shipping Lines whose ships were rusty and lacked cleanliness but they don’t sink or conk out because tale says the Captain is under the pain of death if his ship sinks. But when the company stopped operations because of the tightness of competition in the Verde Island Passage and of some family troubles this ship was one of those which was laid up.

3723482950_fc61c388d5_o

Streamer of Joy-Ruby by Masahiro Homma

In 2003, the ship was sold to Silverio Atienza who was an operator of motor boats called batel in the area. With some modifications and repair, she became the Joy-Ruby, the first steel-hulled ferry of Silverio Atienza which later evolved into the Atienza Shipping Lines. However, once on a voyage to Puerto Princesa she developed a hull in the stern when she was already nearing the port. She continued sailing until she ended up sitting on her stern near the quay with her bow pointing to the sky.

5764897126_0c73ca1e73_b

The Joy-Ruby was subsequently salvaged and sold to Asian Marine Transport Corporation (AMTC) in 2008 where she became the Super Shuttle Ferry 15. For many years she plied the various routes of the company in the Visayas and mainly Ormoc but at times she also experienced some minor problems. This might not really be due to age but to the weakness of her company in maintaining ships. However, her Captain admitted that her engines were not that robust anymore but this is something that could be remedied by re-engining.

Another ship that was also built in 1967 was the Island Express II of Island Shipping Corporation. This ship is a short-distance ferry-cruiser that runs the Bantayan island route although not recently when Island Shipping was already able to build enough passenger-cargo LCTs and the cruisers of the company were already on the way out as cruisers can no longer compete against ROROs except in Zamboanga.

3649598263_9246bbf090_o

Island Express II by Masahiro Homma

The Island Express II was built as the Yuzuru by the Sanriku Shipbuilding & Iron Works in Shiogama, Japan. The ship’s external dimensions are 28.5 meters by 7.0 meters and she is equipped by a single Daihatsu engine of 300 horsepower which means she is a slow craft. This ship came to the Philippines in 1994 when she was already 27 years old. The Island Express II has a passenger capacity of 354 persons all in benches.

Another cruiser ship that was built in 1967 but is an overnight ferry is the Gloria Two of Gabisan Shipping which has fishing vessel origin and was just converted in Leyte. This ferry measures 46.3 meters by 7.7 meters and is now equipped by a single Isuzu Marine engine of 960 horsepower which gives her a cruising speed of 11.5 knots.

8563531617_4a901a1858_k

The Gloria Two is a very reliable ship although she suffers now in competition versus RORO ships. She has a passenger capacity of 386 and she has no other route except the route to Hilongos, Leyte. This ferry is declared to have a Gross Tonnage of 246 with a passenger capacity of 386 person in bunks.

There is another highly-recognizable ship that is well-known in Cebu which is the Lapu-lapu Ferry 1 of Lapu-lapu Shipping. This ship was built by Okayama Shipyard in Hinase, Japan in 1967 and she came to Sweet Lines of the Philippines in 1978. In Sweet Lines she was known as the second Sweet Time doing the Cebu-Tagbilaran-Cagayan de Oro and Cebu-Tagbilaran-Larena-Plaridel routes. Her IMO Number is 7315753.

Sweet Time

Sweet Time by Edison Sy

When Sweet Lines collapsed in 1994, she was laid up for a while until she became the Carmelita. Then she came to Lapu-lapu Shipping which renovated her extensively in 2002 in Villono shipyard until she no longer looked like the old Sweet Time, the reason why people can’t connect her to her origin. But IMO Numbers don’t lie and she was traced.

23558034950_701a9b42c4_z

Lapu-lapu Ferry 1 by Mike Baylon

As Lapu-lapu Ferry 1 her dimensions are 52.2 meters by 8.0 meters by 4.1 meters and she is an overnight ferry-cruiser. Her passenger capacity is 509 and her primary route is Cebu to Cataingan, Masbate. She still has her original Hanshin engine with 1,100 horsepower which is now just good for 8 to 9 knots. To keep up with competition, the ship has an air-conditioned Tourist section.

Another ship built in 1967 is an LCT of E.B. Aznar Shipping of
Danao, the LCT Melrivic 1 which at one time was rumored to be gone but actually was  just hiding in Republic Drydock in Danao City and being re-engined prior to re-fielding. A PSSS (Philippine Ship Spotters Society) tour group found her being refitted in that shipyard. This passenger-cargo LCT is a local-build in Manila.

10959653994_41b602d5f9_k

LCT Melrivic 1 by John Carlos Cabanillas

This vessel’s measurements are 37.4 meters by 8.0 meters which means she is a small LCT and her Gross Tonnage is 321. Originally powered by a single Yanmar Marine engine of 430 horsepower, she is now powered by a Weichai engine of 460 horsepower and her speed increased from 9.5 knots to 11 knots while being more fuel-efficient.

The next ship which is 50 years old now is a respected ship in Bicol but she was not originally a Bicol ferry. In Japan she was known as the Nangokutosa Maru of the Utaka Kokudo Ferry and she was built by Hashihama Zosen in Imabari, Japan. The ship measures 64.0 meters by 11.3 meters with an original Gross Register Tonnage of 904 tons and equipped with twin Daihatsu engines with a total of 2,200 horsepower.

4644972151_94f4f57627_b

Princess of Mayon (parsed from a PPA photo)

In 1990, this ship came to United Towage & Salvage of the Philippines when she was already 23 years old. In this company she was known as Horizon but United Towage & Salvage was actually not into passenger shipping. The ship underwent modifications and she was sold to Bicolandia Shipping Lines where she became known as the Princess of Mayon. For a very long time as in two decades, she was the biggest ferry in Bicol and she was always in the strongest route there, the Matnog to Samar route.

When Bicolandia Shipping Lines was sold lock, stock and barrel to Penafrancia Shipping Lines in 2006, the Princess of Mayon became part of the deal and in the new company she was known as the Don Benito Ambrosio II. She had periods of unreliability soon after. The company’s solution was to build one reliable Daihatsu engine from her two Daihatsu engines and a Yanmar engine was mounted as the second engine.

33156335581_7eefa590cd_k

Now Don Benito Ambrosio II is running well again and she is still in the same route again. The PSSS (Philippine Ship Spotters Society) touring group was able to ride her free last December, “Bridge Class” and know what? Her bridge is air-conditioned! Now, tell me, how many short-distance ferries locally can claim that kind of accoutrement?

The last two vessels that were built in 1967 are both local-builds. Both are small because they were ferries of their companies when they was still young. These two are obsolete now being slow, small cruisers and most of the time they no longer sail. The two are the Ever Transport of Ever Lines and the Magnolia of Magnolia Shipping Corporation, both of Zamboanga City.

8176937651_dc62cc28b9_h

The Ever Transport was built in Cebu and just measures 19.2 meters by 5.1 meters with a Gross Tonnage of just 68 and a passenger capacity of just 87 persons. Her engine is an Isuzu diesel of just 135 horsepower but she can reach 7.5 knots when she was still new. I thought then she was already gone and then I saw her being refitted in Varadero de Cawit in Zamboanga City and they said she will sail again.

Meanwhile, the Magnolia was built by Rato Brothers in Pagadian, Zamboanga del Sur. Her external dimensions are 26.6 meters by 5.4 meters with a Gross Tonnage of 81 and a passenger capacity of 122 persons. The upper half of her hull is wood and the lower half is steel. The Magnolia is powered by a single Caterpillar engine of 120 horsepower. The last time I saw her was she was laid up in Varadero de Recodo in Zamboanga City.

Both the Ever Transport and Magnolia are clearly obsolete now. In passenger capacity they are not even higher than the big passenger-cargo motor bancas which have the same horsepower as them or even more. However, the two can carry more cargo especially since they have high prows and freeboards so they can deal with the sometimes big swells of the seas near Zamboanga.

6449489737_8b5fd169a9_b

Magnolia by Mike Baylon

So that’s it, folks. A total of eight ferries that will be celebrating their 50 years now. Some are already obsolete especially the cruisers because as they say times and modalities change but they are still alive. Do I hear the tune of the BeeGees, “Stayin’ Alive”?

Not all the ferries mentioned have IMO Numbers and some were not traced initially but the cooperation with Angelo Blasutta of the former Grosstonnage.com bore fruit and so the Don Benito Ambrosio II and Lapu-lapu Ferry 1’s origins were traced and both were actually clear surprises.

I always joke that ferries 50 years old should give a discount of 50%, a celebration for being still alive. Oh, it can be not the whole year. Maybe on the month that they were built, at least. And the crew might even be surprised because I found out over the years that many crewmen cannot trace the history of their vessels because they were not trained to look for the IMO Number.

On a future article I will deal with our our ferries built in 1967 that are no longer around and what has happened to them so the people including the haters of old ships will be more educated.